PMC

The hose temperature controller (201312) is a replacement controller for the heated hose circuit on a plural-component proportioner. It reads the hose temperature sensor near the gun and switches hose heat on and off to hold the setpoint, keeping material at spraying temperature all...

The PMC 1/2" x 50' High-Pressure Heated Hose (200024) keeps A and B chemical at spray temperature between a PMC proportioner and the gun, using a copper-weave heating element. Features Rated to 3,500 psi (241 bar) for foam and polyurea Copper-weave heating element Scuff...

The PMC 1/4" x 10' High-Pressure Whip Hose (MA-00040A) is the flexible end section between the heated hose and the spray gun, giving the applicator lighter, easier gun handling. Specifications Part number: MA-00040A Size: 1/4 in x 10 ft Maximum working pressure: 3,500 psi...

The PMC 1/4" x 25' High-Pressure Whip Hose (MA-00040A-25) gives extra reach at the gun end of a heated hose run, so applicators can move without dragging the full hose bundle. Specifications Part number: MA-00040A-25 Size: 1/4 in x 25 ft Maximum working pressure:...

The PMC 2.5 Gallon Solvent Flush Pot Kit (200426) is a pressurized flush pot for cleaning PMC spray guns and whip hoses at the end of the day or before storage. Features 2.5-gallon pressure pot for gun and hose flushing Helps prevent material cure...

The PMC EL-182-25 circuit breaker is a 25 amp, 2-pole breaker carrying a Polyurethane Machinery Corporation (PMC) electrical part number. Breakers in a proportioner's electrical enclosure protect individual circuits from overcurrent, and a failing breaker can trip repeatedly or leave a circuit dead.Features 25...

The PMC 3/8" x 50' High-Pressure Heated Hose (MA-00039A-TC) keeps A and B chemical at spray temperature between a PMC proportioner and the gun, using a copper-weave heating element. Features Rated to 3,500 psi (241 bar) for foam and polyurea Copper-weave heating element No...

The PMC 3/8" x 50' High-Pressure Heated Hose (200008) keeps A and B chemical at spray temperature between a PMC proportioner and the gun, using a copper-weave heating element. Features Rated to 3,500 psi (241 bar) for foam and polyurea Copper-weave heating element Scuff...

The PMC 3/8" x 50' High-Pressure Heated Hose (200007) keeps A and B chemical at spray temperature between a PMC proportioner and the gun, using a copper-weave heating element. Features Rated to 3,500 psi (241 bar) for foam and polyurea Copper-weave heating element Scuff...

The PMC 3/8" x 50' High-Pressure Heated Hose (MA-00039A) keeps A and B chemical at spray temperature between a PMC proportioner and the gun, using a copper-weave heating element. Features Rated to 3,500 psi (241 bar) for foam and polyurea Copper-weave heating element No...

The PMC 3/8" x 50' High-Pressure Heated Hose (200004) keeps A and B chemical at spray temperature between a PMC proportioner and the gun, using a copper-weave heating element. Features Rated to 3,500 psi (241 bar) for foam and polyurea Copper-weave heating element Scuff...

The PMC EL-182 circuit breaker is a 32 amp, 3-pole breaker with a Polyurethane Machinery Corporation (PMC) electrical part number. It protects a three-phase circuit inside the proportioner's electrical enclosure; replace it when it trips without cause or no longer resets.Features 32 amp rating...

The PMC EL-42-3200 pressure switch is a 3200 psi pressure switch from Polyurethane Machinery Corporation. PMC lists it in the final assembly of the PH/PHX-2 proportioner, which uses two of them; pressure switches let the control system react when material pressure exceeds the set...

The PMC 50' TSU Wire Harness (MA-00006A) is a 50 ft extension wire that carries the temperature sensing unit (TSU) signal along a heated hose run back to the proportioner. Specifications Part number: MA-00006A Length: 50 ft Type: TSU extension wire harness Compatibility PMC...

The PMC YS-1 Y-strainer assembly is the A-side (iso) inlet strainer for PMC plural-component proportioners. It filters material before it enters the A-side proportioning pump, protecting pump check valves and downstream components from debris and crystals.Features Complete A-side Y-strainer assembly Protects the A pump...

The PMC air cylinder rebuild kit supplies replacement seals and wear parts for a PMC air cylinder.Features Restores sealing and smooth cylinder travel Replace when the cylinder leaks air or moves sluggishly PMC replacement kit Specifications Store SKU: KT-05025 Brand: PMC Please call ArmorThane...

The PMC KT-06009 air motor repair kit contains replacement wear parts for servicing a PMC air motor.Features Restores air motor performance and reduces air leaks Lets you service the motor instead of replacing it PMC replacement kit Specifications Part number: KT-06009 Brand: PMC Tell...

The PMC AP-2 Air Purge Spray Gun, 01 Mix/Flat Tip Package (GU-AP-2-01-FPKG) is a plural-component gun for spray foam and coatings, set up with an 01 mixing chamber and a flat-pattern tip. Features Air purge clears the mix chamber when the trigger is released...

The PMC AP-2 Air Purge Spray/Pour Gun, 01 Mix/01 Round PCT Package (GU-AP-2-01-PKG) is a lightweight plural-component gun for spray foam and coatings, fitted with a separate mix chamber and a round Pattern Control Tip. Features Separate mixing chamber and Pattern Control Tip (PCT)...

The PMC EL-33 control power supply is a replacement electrical component carrying a Polyurethane Machinery Corporation (PMC) part number. A control power supply feeds low-voltage power to a proportioner's control circuit, so a failure can leave displays, controllers or relays without power.Features Replacement control...

The PMC Coupling Block Flush Kit, F-AP (200218) is a flushing kit that connects at the coupling block of PMC air-purge spray guns for solvent cleaning. Specifications Part number: 200218 Type: Coupling-block flush kit Compatibility PMC air-purge guns. Call (417) 831-5090 to confirm fit...

The PMC Diamond-Plated Chamber/PCT Kit #01 (KT-814-DP-01) bundles a #01 diamond-plated mixing chamber with a matching round Pattern Control Tip for the PMC Xtreme air purge gun. Features Diamond-plated chamber for scratch resistance and long service life Matched round PCT for a consistent spray...

The PMC Diamond-Plated Mixing Chamber #01 (GU-814-DP-01) is the replacement mix chamber for the PMC Xtreme spray gun, where both components impinge and mix before leaving the gun. Features Diamond plating with 36% higher scratch resistance, per PMC PMC reports up to 60 sets...