PMC

This PMC spool valve liner (stock GUN-LSV2) is the stationary sleeve the trigger spool slides in on PMC air-purge spray guns. When it wears, air bypasses the spool and the gun may open or close slowly, so replacing the liner with the spool is...

The PMC EL-51A-2 is the replacement sensor for PMC's heated-hose Temperature Sensing Unit (TSU, assembly EL-51A-4). PMC recommends installing the TSU between the last section of heated hose and the gun whip, so the hose heat controller reads material temperature close to the gun.Features...

The PMC TSU (Temperature Sensing Unit) Block Assembly (EL-51A-4) measures fluid temperature in a PMC heated hose so the proportioner can control hose heat accurately. Features Designed for a smaller hose bundle diameter at the TSU connection Consolidates the chemical and air hose connections...

The PMC 202220 vertical sleeve (cage) is a replacement pump component for PMC spray foam and coatings equipment.Features Genuine PMC part number Replace when worn or damaged during pump service Often serviced with PMC pump base parts such as the 202221 retaining nut Specifications...

The PMC Xtreme Air Purge Spray Gun, 01 Chamber/PCT Package (202724) is PMC's simplified, high-reliability spray and pour gun for foam and coatings. Features Diamond-plated mixing chambers (GU-814-DP series); PMC reports up to 60 sets sprayed on one chamber Engineered resin side seals Spool-and-liner...

The PMC Xtreme Air Purge Spray Gun, 01 Chamber/PCT Package, Steel (202725) is the steel version of PMC's Xtreme gun for spray foam and coatings. Features Diamond-plated 01 mixing chamber with Pattern Control Tip Engineered resin side seals Spring-loaded check valve helps prevent chemical...

The PMC Xtreme air-purge spray gun with 00 chamber (PMC 202718, Xtreme w/00 chamber/PCT pkg) is a plural-component gun for spray foam and polyurea coatings. PMC built the Xtreme by combining the most useful features of its AP-2 and AP-3 guns, and the 00...

The PMC Xtreme aluminum block (PMC 203290, Gun Block, CV, Xtreme, AL) is the main fluid block of the PMC Xtreme air-purge spray gun. It carries the A and R side ports and check valves that feed material to the mixing chamber, and the...

This hex bolt (GUN-HB) is replacement hardware for the PMC Xtreme air-purge spray gun. Gun hardware takes a beating from repeated teardowns for cleaning and rebuilds, and a stretched or rounded bolt can keep the gun from assembling squarely.Features Replaces stripped, rounded or lost...

The GUN-HCB hex cap bolt is replacement fastening hardware for the PMC Xtreme plural-component spray gun. Swapping a damaged cap bolt during a rebuild helps the gun go back together tight and square so it seals and cycles properly.Features Replaces a damaged or missing...

The GUN-SB shoulder bolt is replacement hardware for the PMC Xtreme air-purge spray gun. PMC's Xtreme parts list calls for two stainless shoulder bolts in the final gun assembly, and these small parts are easy to lose or damage during cleaning.Features Stainless steel for...

The PMC Xtreme Side Seal, .125 Engineered Resin (202454) seals each chemical port against the mixing chamber on the PMC Xtreme gun. Features Engineered resin side seal, part of the Xtreme gun's reliability design Common wear item to keep on hand Specifications Part number:...

The PMC Xtreme Full Gun Rebuild Kit (202757) contains the wear parts needed to restore a PMC Xtreme air purge spray and pour gun to working condition. Features One kit covers a complete gun rebuild Keeps a spare on the rig to avoid downtime...

The PMC Xtreme piston assembly is the air piston that drives the PMC Xtreme air-purge spray gun open and closed. The trigger's spool valve routes air to the front or rear of this piston, which moves the mixing chamber, so a worn piston or...

The PMC RA-00074-02A is the replacement gasket for the RA-00074-00A Y-strainer on the inlet side of PMC PH/PHX-series proportioners.Features Seals the strainer cap after screen cleaning or replacement Replace whenever the gasket is flattened, torn or chemically attacked Genuine PMC part Specifications Part number:...

The PMC RA-00074-03-60A is a 60 mesh replacement screen for the Y-strainers on PMC plural-component proportioners. The Y-strainer filters incoming material before it reaches the proportioning pumps, protecting check valves and the spray gun from debris and crystallized material.Features 60 mesh replacement screen Fits...