High Pressure Rebuild Kits

The Graco 246355 complete O-ring kit contains the O-rings needed to fully reseal a Graco Fusion AP air-purge spray gun.Before servicing any Fusion gun, follow the Pressure Relief Procedure in the Graco manual and close the manifold valves.Features Covers side seals, cartridges, check valves,...

The Carlisle 336429 safety stop assembly kit restores the safety stop on the Carlisle ST1 air-purge spray foam gun. Related parts include the 336737 safety stop knob and 336413 safety stop o-rings. The ST1's Ultra Onyx coated body is built for easier cleaning and...

The Carlisle 336426 front end assembly kit is a complete front end assembly for the Carlisle ST1 spray foam gun, a fast way to recover a gun with a damaged or heavily fouled front end. The ST1 uses an air-purge design with an integral...

This Graco Probler P2 side seal kit is built around the GC2498 stainless steel side seal used on the Graco (GlasCraft) Probler P2, an air-purge plural-component dispense gun for non-flammable spray foam and polyurea. Graco's own P2 side seal kit, part number GC1946, contains...

This Probler P2 o-ring kit supplies replacement o-rings for rebuilding the Graco/GlasCraft Probler P2 dispense gun. O-rings harden and wear with heat, chemicals and solvent, and replacing them as a set is the fastest way to cure air leaks and sluggish triggering.Features Reseals the...

The PMC KT-07002 is PMC's current 80 A Pump Rebuild Kit for the size 80 A (ISO) proportioning pump, PU-05001-80.Features Includes the PU-03001 triple lip seal, PU-03006 shaft bearing, PU-01016A-008 piston seal, PU-03016 retaining ring and O-rings per PMC's rebuild instructions Triple lip shaft...

The PMC KT-05001-60 is the rebuild kit for the size 60 A (ISO) proportioning pump used on PMC hydraulic proportioners.Features Size 60 seals and wear items for the ISO pump Restores consistent pressure and helps prevent ISO leakage PMC replacement kit Specifications Part number:...

The PMC KT-05001-40 is the rebuild kit for the size 40 A (ISO) proportioning pump on PMC hydraulic proportioners.Features Size 40 seals and wear parts for the ISO pump Stops leaks and pressure dive on the A side PMC replacement kit Specifications Part number:...

This PMC pump rebuild kit is intended for the proportioning pumps on PMC PH-20 / PHX-20 proportioners, supplying the seals and wear parts needed to service a leaking or low-output pump.Features Restores pump sealing and consistent pressure Cost-effective alternative to replacing a complete pump...

The PMC KT-06009 air motor repair kit contains replacement wear parts for servicing a PMC air motor.Features Restores air motor performance and reduces air leaks Lets you service the motor instead of replacing it PMC replacement kit Specifications Part number: KT-06009 Brand: PMC Tell...

The PMC KT-05025 hydraulic cylinder rebuild kit restores the hydraulic drive cylinder that powers the pumpline on PMC PH/PHX-series proportioners.Features Replacement seals for the hydraulic drive cylinder Fixes hydraulic oil leaks and loss of drive force Lower-cost alternative to replacing the cylinder Genuine PMC...

The PMC KT-05021 heater thermocouple kit replaces the temperature sensor in the primary heaters of PMC PH/PHX-series proportioners.Features Accurate temperature feedback to the heater controller Fixes erratic, frozen or missing heater temperature readings Genuine PMC kit Specifications Part number: KT-05021 Brand: PMC Description: Heater...

The PMC KT-05004 lube hose assembly kit is PMC's ISO lube reservoir/hose kit, supplying the reservoir components, tubing and check valve that circulate pump lube to the ISO pump on PMC PH/PHX-series proportioners.Features Complete lube circuit replacement for the ISO pump Includes the RA-00068A...

The PMC KT-05002-40 is the rebuild kit for the size 40 R (resin, B-side) proportioning pump used on PMC hydraulic proportioners.Features Size 40 seals and wear items for the resin pump Helps restore consistent pressure and on-ratio output PMC replacement kit Specifications Part number:...

The PMC KT-05002-120 is the 120 Resin Pump Rebuild Kit for the R (B-side) proportioning pump on PMC PH/PHX-series proportioners.Features Complete set of seals and wear items for a size 120 resin pump Includes cylinder bearing, flange gasket, piston support washer, piston seal wiper,...

The PMC KT-05002-080 is the 80 Resin Pump Rebuild Kit for the size 80 R (B-side) proportioning pump on PMC PH/PHX-series proportioners.Features 80-size seals and wear parts for the resin pump Restores pumping efficiency and consistent pressure Genuine PMC kit Specifications Part number: KT-05002-080...

The PMC KT-05001-120 is the 120 ISO (A-side) pump rebuild kit for PMC PH/PHX-series proportioners, containing the seals and wear parts needed to restore a leaking or low-pressure A pump.Features Restores sealing on the ISO pump to stop leaks and pressure dive Includes the...

The spool valve rebuild kit (GUN-SVRK) contains replacement parts for servicing the spool valve in a plural-component spray gun handle. The spool valve directs trigger air to open and close the gun, so worn parts show up as air leaks, a sticky trigger or...

The PMC air cylinder rebuild kit supplies replacement seals and wear parts for a PMC air cylinder.Features Restores sealing and smooth cylinder travel Replace when the cylinder leaks air or moves sluggishly PMC replacement kit Specifications Store SKU: KT-05025 Brand: PMC Please call ArmorThane...

The PMC KT-05005 inlet monitoring kit adds monitoring to the A and R material inlets of PMC PH/PHX-series proportioners so you can see feed conditions before problems reach the gun.Features Helps catch starved or restricted feed early Supports troubleshooting of transfer pump and strainer...