Shop All

The PMC screen screw assembly, A side (part 202409, stock GUN-SSA), filters the A-side (isocyanate) material as it enters the gun on PMC AP-2, AP-3 and Xtreme air-purge spray guns. Catching debris before the side seal and mixing chamber helps prevent crossover, plugged impingement...

The PMC screen screw assembly, R side (part 202410, stock GUN-SSR), is the resin-side inlet filter for PMC AP-2, AP-3 and Xtreme spray guns. It screens the B-side (resin/poly) material entering the gun so particles do not reach the side seal or plug the...

The PMC 202305 pump base kit is PMC's split-sleeve pump base upgrade kit for PMC proportioning pumps. It was previously sold under PMC part number PU-05022A.Features Upgrades the pump base to PMC's split-sleeve design Pairs with related PMC pump base parts such as the...

The Graco 106555 is an o-ring used in the Graco/GlasCraft Probler P2 dispense gun. Graco's parts list shows two 106555 o-rings in the P2 air switch assembly (GC0128), and it is also included in Graco's GC1937 standard P2 repair kit.Features Stops air leaks at...

The PMC 202221 retaining nut secures the pump base components on PMC proportioning pumps.Features Holds the pump base assembly together Replace if threads are damaged or the nut is cracked Often serviced alongside the 202305 split-sleeve pump base kit Genuine PMC part Specifications Part...

The PMC 202220 vertical sleeve (cage) is a replacement pump component for PMC spray foam and coatings equipment.Features Genuine PMC part number Replace when worn or damaged during pump service Often serviced with PMC pump base parts such as the 202221 retaining nut Specifications...

The Air Cylinder Bushing (GUN-ACB) is a replacement bushing for the air cylinder of a high-pressure spray gun, used when rebuilding the gun's air section. Specifications Part number: GUN-ACB (ArmorThane stock number) Type: Air cylinder bushing Compatibility Call ArmorThane at (417) 831-5090 to confirm...

The hose temperature controller (201312) is a replacement controller for the heated hose circuit on a plural-component proportioner. It reads the hose temperature sensor near the gun and switches hose heat on and off to hold the setpoint, keeping material at spraying temperature all...

The heater temperature controller (201310) is a replacement controller for the material heater on a plural-component proportioner. The controller reads the heater temperature sensor and switches heater power to hold the setpoint, which is critical for proper viscosity and mixing of spray foam and...

The GUN-SB shoulder bolt is replacement hardware for the PMC Xtreme air-purge spray gun. PMC's Xtreme parts list calls for two stainless shoulder bolts in the final gun assembly, and these small parts are easy to lose or damage during cleaning.Features Stainless steel for...

This hex bolt (GUN-HB) is replacement hardware for the PMC Xtreme air-purge spray gun. Gun hardware takes a beating from repeated teardowns for cleaning and rebuilds, and a stretched or rounded bolt can keep the gun from assembling squarely.Features Replaces stripped, rounded or lost...

The GUN-HCB hex cap bolt is replacement fastening hardware for the PMC Xtreme plural-component spray gun. Swapping a damaged cap bolt during a rebuild helps the gun go back together tight and square so it seals and cycles properly.Features Replaces a damaged or missing...

The ArmorThane O-ring (stock SPR164) is a replacement seal for the pumps on ArmorThane low-pressure spray machines.Features Restores a leak-free static seal Replace whenever the pump is opened Pairs with the SPR162 lip seal and SPR163 needle bearing Specifications Stock number: SPR164 Description: O-ring...

The Graco 16P010 check valve filter is used on both sides of the Graco/GlasCraft Probler P2 dispense gun. It filters the A and B materials entering the gun and provides a check function that helps prevent crossover.Features Filters material before the mix chamber Helps...

The Graco GC2548 is a GlasCraft-series Probler trigger supplied by Graco. A bent or worn trigger can make it hard to fully open or close the gun, so a new trigger restores positive control.Features Genuine Graco (GlasCraft) GC-series part Restores positive trigger control Replace...

The ArmorThane PKG140 is a cleaning drill bit for 00-size mix chambers on plural-component spray foam and polyurea guns. Used in a pin vise, a correctly sized drill clears cured material from the chamber bore without enlarging it, which keeps spray pattern and mixing...

The Graco Fusion FX fluid cartridge kit supplies the replaceable FX fluid cartridge that sits at the heart of the Graco Fusion FX plural-component spray gun. The cartridge controls fluid flow through the gun's impingement mixing and houses the shuttle valves that switch between...

The Graco 16N600 is the resin (poly, B-side) side block for the Graco/GlasCraft Probler P2 dispense gun. It routes resin from the hose connection through the check valve filter and seals into the mix chamber.Features B-side fluid block for the P2 Replace after crossover...

The Graco 16N599 is the ISO (A-side) side block for the Graco/GlasCraft Probler P2 dispense gun. The side block carries isocyanate from the hose connection through the check valve filter, seal and side seal into the mix chamber.Features A-side fluid block for the P2...

The Graco 15B772 air hose is the short 18 in. air whip that connects the air supply to Graco plural-component spray guns. Graco lists it as the 1/4 NPSM (fbe) air hose on the Probler P2 and as the 18 in. air hose on...

The Graco 15U395 adapter is a 1/8 in. NPT male x female fitting that appears in the parts lists of both the Graco Probler P2 and the Graco Fusion CS plural-component spray guns, each using two per gun.Features Genuine Graco part 15U395 1/8 in....

The Graco 117635 is the #5 JIC swivel union hose fitting used on the ISO (A) side of the Graco/GlasCraft Probler P2 dispense gun. The swivel lets the whip hose rotate freely at the gun, reducing strain on the connection and the operator's wrist.Features...

The Graco 117634 is the #6 JIC swivel union hose fitting on the resin (B) side of the Graco/GlasCraft Probler P2 dispense gun. It lets the whip hose rotate at the gun so the operator is not fighting hose twist all day.Features #6 JIC...