Shop All

The ArmorThane Air Angle Sander (EQU104) is a pneumatic angle sander for surface preparation. Scuffing and profiling the substrate before spraying helps coatings bond, making this a core prep tool for bedliner and polyurea applicators. Features Air-powered: runs off your shop compressor Angle-head design...

PRE106 36-inch masking paper covers wide areas quickly when masking vehicles, walls, floors and equipment before spraying polyurea, bedliners or topcoats.Features 36" width covers large panels in fewer passes Use with masking tape for sharp, protected edges Helps keep overspray off surfaces that should...

PRE108 static cling sheeting is a masking film that clings to surfaces, making it quick to cover vehicles, glass and equipment before spraying.Features Static cling helps the film stay in place Covers large areas fast with less tape Protects against overspray drift Specifications Stock...

ArmorThane ArmorLiner is a two-component, liquid spray-applied polyurea liner system that is compatible with nearly any substrate, including metal, concrete, fiberglass and wood. It is ArmorThane's all-purpose polyurea and its most widely used product.Features Simple 1:1 mix ratio for easy proportioning Fast polyurea cure...

E-Z Wire Trim Tape (PRE107) is a wire-reinforced trim tape used to create clean, professional edges where a sprayed coating meets an uncoated surface.Features Embedded wire helps cut a crisp line through fresh coating Ideal around bedliner rails, trim and body lines Reduces time...

EZ Trim Fiber Tape (PRE104) is a fiber-reinforced trim tape for producing neat edges where sprayed bedliner or polyurea meets painted or trim surfaces.Features Fiber reinforcement for a clean pull and cut line Great around bed rails, tailgates and body lines Cuts down on...

PRE102 1-1/2" masking tape secures masking paper and sheeting and protects wider edges before spraying polyurea, bedliner and topcoats.Features 1-1/2" width for wider coverage along edges Holds masking paper and plastic sheeting in place Easy to tear by hand Specifications Stock number: PRE102 Width:...

PRE100 3/4" masking tape is a narrow tape for detail masking around trim, lights, fittings and tight curves before spraying.Features 3/4" width follows curves and small parts Use with masking paper and trim tape for complete protection Tears cleanly by hand Specifications Stock number:...

ArmorThane PLM-100 is a two-component polyurea designed specifically as a pipe lining material, part of ArmorThane's low-pressure ArmorLine series. It protects pipes from corrosion caused by the fluids they carry or by surrounding moisture.Features Solvent-free with no VOCs Does not peel or flake Adds...

ArmorThane ArmorFloor Tan is ArmorFloor's two-component aliphatic polyaspartic in a warm tan color. Its resilience, durability and UV resistance make it suitable for indoor and outdoor floors and as a colored topcoat over polyurea.Benefits Tan color for a softer, natural look Holds up to...

ArmorThane ArmorFloor Grey is the grey-pigmented version of ArmorFloor, a two-component aliphatic polyaspartic floor coating for moderate to severe chemical environments. Grey gives shops and warehouses a clean industrial look that hides wear.Benefits Chemical resistance for industrial and commercial floors UV resistant – suitable...

ArmorThane ArmorFloor Clear is a two-component aliphatic polyaspartic coating for moderate to severe chemical environments, indoors or out. ArmorThane calls ArmorFloor its most versatile roll-on product – used for flooring, topcoating polyurea and boosting chemical resistance.Features Resilient, durable and UV resistant Glossy clear finish...

ArmorThane ArmorDeck Topcoat Clear is a polyester, aliphatic, single-component, liquid-applied, moisture-cured urethane polyurea surface protection coating. It finishes the ArmorDeck system with a colorfast, weatherable layer.Features Aliphatic chemistry for UV resistance and colorfastness Excellent abrasion resistance and weatherability Single component; rolls on easily Clear...

ArmorThane ArmorDeck Basecoat is a single-component, high-solids, solvent-free, low-odor, liquid-applied, moisture-cured aromatic urethane polyurea elastomeric waterproofing base membrane. It is the foundation layer of the roll-on ArmorDeck system.Features Single component – no mixing or spray rig required Seamless, waterproof elastomeric membrane Solvent-free and low...

ArmorThane UltraTech is a 1:1, fast-set, spray-applied hybrid polyurea elastomer that is 100% solids and VOC free. It forms a smooth, slick surface that is hard and tough yet resilient – ArmorThane's most wear-resistant material.Features Outstanding abrasion and friction resistance Very high tensile and...

ArmorThane UltraBlast is a two-component, 1:1, fast-set, spray-applied polyurea made of 100% solids. Its hybrid formulation creates a smooth but hard, slick yet tough barrier engineered for blast mitigation and severe service.Features Exceptional toughness and blast mitigation capability Highly abrasion-resistant and chemically tolerant Compatible...

ArmorThane SureGrip is a two-component, fast-setting, rapid-curing soft polyurea designed as a slip-resistant coating for metal and concrete. ArmorThane reports it has the highest coefficient of friction of any of its polyurea products.Features Maximum slip resistance in ArmorThane's internal testing Greatest elongation of any...

ArmorThane STS-300 is an all-purpose 2:1 low-pressure polyurethane coating for truck bedliners, flooring, roofing and marine surfaces. Compared with STS-200 it is less flexible and has greater Shore hardness.Features Resists cracking, peeling and deformation under continuous strain Enhanced chemical resistance and lower permeability Higher...

ArmorThane STS-200 is a 2:1 polyurethane free of mercury, VOCs and TDI, designed as a liner for metals, concrete, fiberglass, wood and some plastics. It is sprayed with ArmorThane low-pressure equipment such as the ArmorLine LP Series 4121 and E-Z Gun.Features 100% solids; low...

ArmorThane HighLine 610 is a 1:1, fast-setting, spray-applied two-component polyurea with 100% solids and zero VOCs. It resists cold break and can be applied at substrate and ambient temperatures from 0°F, making it a strong choice for containment liners and geotextile fabric.Features Low application...

ArmorThane HighLine 610 spray polyurea is supplied as a 100-gallon kit for high-pressure plural-component equipment. Developed with newer liner materials such as geotextile fabrics in mind, it gels in about 10 seconds and is tack-free in about 60 seconds.Benefits Seamless liner with a balance...

ArmorThane HighLine 510H is the harder, tougher industrial version of HighLine 510 – a fast-setting, rapid-curing, 100% solids aromatic pure polyurea for prepared concrete and metal. Its extremely fast gel lets crews apply it at temperatures as low as 20°F (-6°C).Features More hardness and...

ArmorThane HighLine 510 is a two-component, spray-applied pure polyurea designed to protect well-prepared concrete and metal surfaces. It is part of ArmorThane's high-pressure ArmorLine series and is built to get the most out of polyurea's natural moisture resistance.Features Coats carbon and mild steel without...