Shop All

The HV HP transfer pump (SPR184) is a drum transfer pump used to feed material from the supply drum to a plural-component proportioner. A reliable transfer pump keeps the proportioner inlet supplied so it can hold ratio and pressure during spraying.Features Transfer pump for...

The PMC HI-05047 pump to heater hose is the 16.25 inch fluid hose that carries material from the proportioning pump outlet to the primary heater on PMC proportioners.Features Pre-made length for a direct replacement Replace hoses that are leaking, kinked or chemically damaged Genuine...

The PMC HI-05040-2 hydraulic gauge is a variant of PMC's HI-05040 hydraulic pressure gauge for PMC hydraulic spray foam and polyurea proportioners.Features Replacement pressure gauge for the proportioner's hydraulic system Lets you monitor hydraulic drive pressure while spraying Swap out a damaged or inaccurate...

The PMC HI-05040 hydraulic gauge is the 0–2000 psi pressure gauge used on the hydraulic cylinder assembly of PMC PH/PHX-series hydraulic proportioners.Features Displays hydraulic drive pressure so you can set and monitor the system 0–2000 psi scale sized for the proportioner's hydraulic circuit Replace...

The PMC HI-00067 hydraulic pump Magnaloy insert is the flexible element of the jaw-style coupling that links the electric motor to the hydraulic pump on PMC hydraulic proportioners.Features Flexible coupling element that transmits motor torque to the hydraulic pump Helps absorb start-up shock and...

The PMC HI-00065-01 Magnaloy insert is the flexible spider that sits between the two Magnaloy hubs in the bell housing, coupling the electric motor to the hydraulic pump on PMC PH/PHX proportioners.Features Transmits motor torque to the 18cc hydraulic pump Cushions shock loads and...

The PMC HI-00035 pressure gauge is the 0–5000 psi (345 bar) fluid pressure gauge used on PMC PHX-series high-pressure proportioners.Features Shows material pressure so operators can spot pressure imbalance, a key sign of off-ratio spraying 0–5000 psi scale suited to PHX high-pressure polyurea and...

The PMC RA-00074-03-60A is a 60 mesh replacement screen for the Y-strainers on PMC plural-component proportioners. The Y-strainer filters incoming material before it reaches the proportioning pumps, protecting check valves and the spray gun from debris and crystallized material.Features 60 mesh replacement screen Fits...

The PMC RA-00074-02A is the replacement gasket for the RA-00074-00A Y-strainer on the inlet side of PMC PH/PHX-series proportioners.Features Seals the strainer cap after screen cleaning or replacement Replace whenever the gasket is flattened, torn or chemically attacked Genuine PMC part Specifications Part number:...

The PMC RA-00068A check valve is the one-way valve used in the ISO lube reservoir and hose assembly (kit KT-05004) of PMC PH/PHX-series proportioners.Features Allows pump lubricant to circulate in one direction only Helps protect the ISO pump seals by keeping the lube system...

The PMC RA-00065A is a small fitting from the pumpline lube cylinder area of PMC PH/PHX-series proportioners, sold here as the pump lube cylinder plug.Features Replaces a cracked, stripped or leaking lube fitting Helps keep the pump lube system sealed Genuine PMC part Specifications...

The PMC PU-05026 tie rod is the 3/8-24 threaded rod that clamps the proportioning pump assembly together on PMC PH/PHX-series proportioners.Features Holds pump components in alignment under spraying pressure Replace bent or thread-damaged rods during pump service Used across multiple PMC pump sizes Genuine...

The PMC PU-05025 discharge ball is the outlet check ball of the PMC proportioning pump. It seals against the PU-05024 discharge ball seat on each stroke.Features Controls one-way flow out of the pump on the pressure stroke Replace with the seat when you see...

The PMC PU-05024 discharge ball seat is the outlet check seat in the PMC proportioning pump that the PU-05025 discharge ball closes against.Features Provides the sealing surface for the discharge check Worn or chipped seats cause pressure loss and ratio problems Genuine PMC part,...

The PMC PU-05021 pump spring is the check valve spring used with the inlet ball and seat in PMC proportioning pumps.Features Helps the check ball return and seat consistently A weak or broken spring can cause erratic pressure and poor fill Low-cost part worth...

The PMC PU-05020 inlet ball is the intake check ball of the PMC proportioning pump, sealing against the PU-05019 inlet ball seat.Features Lets material into the pump on the intake stroke and seals on the pressure stroke A worn or stuck inlet ball causes...

The PMC PU-05019 inlet ball seat is the intake check seat in the PMC proportioning pump that the PU-05020 inlet ball seals against.Features Sealing surface for the inlet check valve Replace when pitted, chipped or worn to stop pressure dive on the intake side...

The PMC PU-05007 pump clevis pin is the pin that secures the clevis connection in the pumpline assembly of PMC PH/PHX-series hydraulic proportioners.Features Holds the clevis joint between the hydraulic drive and the pumpline Replace a worn or bent pin to remove play in...

The PMC PU-05006 hydraulic clevis is the pumpline connector that couples the hydraulic cylinder shaft to the proportioning pump drive on PMC hydraulic spray foam and polyurea proportioners.Features Transfers the hydraulic cylinder's reciprocating force to the pumpline Pairs with the PMC PU-05007 pump clevis...

The PMC PU-05003 lube cylinder is the pump lubrication cylinder from the pumpline assembly of PMC PH/PHX-series hydraulic proportioners.Features Holds pump lubricant at the ISO pump shaft to help keep isocyanate from crystallizing on the seals Replace if cracked, leaking or damaged Works with...

The PMC PU-05002-80 is the complete size 80 "R" (resin/polyol) proportioning pump assembly used on PMC PH/PHX-series hydraulic proportioners.Features Complete R-side assembly to minimize downtime Size 80 is one of the two pump sizes PMC lists for the PH(X)-25 and PH(X)-40 Rebuildable with KT-05002-080...

The PMC PU-05002-40 is the complete size 40 "R" (resin/polyol) proportioning pump assembly for PMC hydraulic proportioners.Features Complete R-side pump for a quick change-out Smaller displacement size suited to lower-output setups Rebuildable with PMC size 40 R kits (KT-05002-40; PMC now lists KT-07007) Genuine...

The PMC PU-05002-120 is the complete size 120 "R" (resin/polyol) proportioning pump assembly for PMC PH/PHX-series hydraulic proportioners.Features Complete R-side pump assembly for fast replacement instead of a bench rebuild Size 120 is the pump size PMC uses for maximum output on the PH(X)-25...