Parts & Rebuild Kits

The PMC air cylinder rebuild kit supplies replacement seals and wear parts for a PMC air cylinder.Features Restores sealing and smooth cylinder travel Replace when the cylinder leaks air or moves sluggishly PMC replacement kit Specifications Store SKU: KT-05025 Brand: PMC Please call ArmorThane...

The PMC Xtreme aluminum block (PMC 203290, Gun Block, CV, Xtreme, AL) is the main fluid block of the PMC Xtreme air-purge spray gun. It carries the A and R side ports and check valves that feed material to the mixing chamber, and the...

The Graco GC0259 check valve ball is a 1/4 in. diameter, 302 stainless steel ball found in the Probler P2, P2 Elite and Auto Probler P2 parts lists. It is small, easily lost during cleaning, and important for the gun to function correctly.Features Corrosion-resistant...

The PMC spool valve (stock GUN-SV) is the moving part of the trigger air valve on PMC air-purge spray guns. When you pull the trigger, the spool shifts inside its liner and routes air to the front or rear of the air piston, opening...

The GUN-LSV spool valve liner is a replacement part for the trigger air valve of PMC air-purge spray guns. The spool rides inside the liner and directs air to the front or rear of the air piston, opening and closing the mixing chamber as...

This Graco Probler P2 side seal kit is built around the GC2498 stainless steel side seal used on the Graco (GlasCraft) Probler P2, an air-purge plural-component dispense gun for non-flammable spray foam and polyurea. Graco's own P2 side seal kit, part number GC1946, contains...

The Graco GC2498 side seal is the stainless steel (SST) side seal for the Graco (GlasCraft) Probler P2, an air-purge plural-component dispense gun for non-flammable spray foam and polyurea. The side seals ride against the mixing chamber and keep the A (ISO) and B...

The PMC screen screw assembly, A side (part 202409, stock GUN-SSA), filters the A-side (isocyanate) material as it enters the gun on PMC AP-2, AP-3 and Xtreme air-purge spray guns. Catching debris before the side seal and mixing chamber helps prevent crossover, plugged impingement...

The PMC screen screw assembly, R side (part 202410, stock GUN-SSR), is the resin-side inlet filter for PMC AP-2, AP-3 and Xtreme spray guns. It screens the B-side (resin/poly) material entering the gun so particles do not reach the side seal or plug the...

The PMC 202305 pump base kit is PMC's split-sleeve pump base upgrade kit for PMC proportioning pumps. It was previously sold under PMC part number PU-05022A.Features Upgrades the pump base to PMC's split-sleeve design Pairs with related PMC pump base parts such as the...

The Graco 106555 is an o-ring used in the Graco/GlasCraft Probler P2 dispense gun. Graco's parts list shows two 106555 o-rings in the P2 air switch assembly (GC0128), and it is also included in Graco's GC1937 standard P2 repair kit.Features Stops air leaks at...

The PMC 202221 retaining nut secures the pump base components on PMC proportioning pumps.Features Holds the pump base assembly together Replace if threads are damaged or the nut is cracked Often serviced alongside the 202305 split-sleeve pump base kit Genuine PMC part Specifications Part...

The PMC 202220 vertical sleeve (cage) is a replacement pump component for PMC spray foam and coatings equipment.Features Genuine PMC part number Replace when worn or damaged during pump service Often serviced with PMC pump base parts such as the 202221 retaining nut Specifications...

The Air Cylinder Bushing (GUN-ACB) is a replacement bushing for the air cylinder of a high-pressure spray gun, used when rebuilding the gun's air section. Specifications Part number: GUN-ACB (ArmorThane stock number) Type: Air cylinder bushing Compatibility Call ArmorThane at (417) 831-5090 to confirm...

The hose temperature controller (201312) is a replacement controller for the heated hose circuit on a plural-component proportioner. It reads the hose temperature sensor near the gun and switches hose heat on and off to hold the setpoint, keeping material at spraying temperature all...

The heater temperature controller (201310) is a replacement controller for the material heater on a plural-component proportioner. The controller reads the heater temperature sensor and switches heater power to hold the setpoint, which is critical for proper viscosity and mixing of spray foam and...

The GUN-SB shoulder bolt is replacement hardware for the PMC Xtreme air-purge spray gun. PMC's Xtreme parts list calls for two stainless shoulder bolts in the final gun assembly, and these small parts are easy to lose or damage during cleaning.Features Stainless steel for...

This hex bolt (GUN-HB) is replacement hardware for the PMC Xtreme air-purge spray gun. Gun hardware takes a beating from repeated teardowns for cleaning and rebuilds, and a stretched or rounded bolt can keep the gun from assembling squarely.Features Replaces stripped, rounded or lost...

The GUN-HCB hex cap bolt is replacement fastening hardware for the PMC Xtreme plural-component spray gun. Swapping a damaged cap bolt during a rebuild helps the gun go back together tight and square so it seals and cycles properly.Features Replaces a damaged or missing...

The ArmorThane O-ring (stock SPR164) is a replacement seal for the pumps on ArmorThane low-pressure spray machines.Features Restores a leak-free static seal Replace whenever the pump is opened Pairs with the SPR162 lip seal and SPR163 needle bearing Specifications Stock number: SPR164 Description: O-ring...

The Graco 16P010 check valve filter is used on both sides of the Graco/GlasCraft Probler P2 dispense gun. It filters the A and B materials entering the gun and provides a check function that helps prevent crossover.Features Filters material before the mix chamber Helps...

The Graco GC2548 is a GlasCraft-series Probler trigger supplied by Graco. A bent or worn trigger can make it hard to fully open or close the gun, so a new trigger restores positive control.Features Genuine Graco (GlasCraft) GC-series part Restores positive trigger control Replace...

The Graco Fusion FX fluid cartridge kit supplies the replaceable FX fluid cartridge that sits at the heart of the Graco Fusion FX plural-component spray gun. The cartridge controls fluid flow through the gun's impingement mixing and houses the shuttle valves that switch between...