Graco Fusion AP Gun Parts

The Graco 117510 air line coupler is the 1/4 in. NPT coupler used on the air line of Graco Fusion AP, Fusion CS and Fusion MP spray guns, mating with the 117509 male quick-disconnect at the gun.Features Genuine Graco air line coupler 1/4 in....

Keep your Fusion AP gun sealing properly with the Amaano Amaano Cleanoff Air Valve O-Ring, Reusable (246354-R), made for the gun's cleanoff air valve. Features Matches the Graco Fusion AP cleanoff air valve position (Graco part 246354) Field-tested by spray foam contractors in addition...

Graco 246354 is a 6-pack of O-rings used on Graco Fusion guns; on the Fusion AP and PC it seals the clean-off air valve, and on the Fusion CS it is a check valve O-ring.Worn seals and O-rings are the most common cause of...

Amaano Small Piston O-Ring, Reusable (248134-R) is an aftermarket o-ring for the small piston position on Graco Fusion AP spray foam guns. Features Matches the Graco Fusion AP small piston position (Graco part 248134) Field-tested by spray foam contractors in addition to lab testing,...

The Graco 15B203 piston is the air piston that sits inside the cylinder of Graco Fusion AP and Fusion PC spray guns (ref. 15). Air pressure acting on this piston opens and closes the gun when you pull and release the trigger, so a...

Graco 248134 is a package of 6 piston shaft O-rings for the Graco Fusion AP air-purge spray gun, sealing the air piston shaft.Before servicing any Fusion gun, follow the Pressure Relief Procedure in the Graco manual and close the manifold valves.Features 6 O-rings per...

The Graco 100721 pipe plug is a 1/4-18 NPT plug listed on the Graco Fusion AP (air-purge) spray gun, where Graco notes it is used on round and flat pattern guns only. It is also listed in the Fusion CS and Fusion MP parts...

Amaano 248134-D supplies small piston o-rings for the small piston on Graco Fusion AP guns, ready for scheduled rebuilds. Features Matches the Graco Fusion AP small piston position (Graco part 248134) Field-tested by spray foam contractors in addition to lab testing, per the supplier...

The Graco 119626 muffler is the replacement muffler listed in the parts lists of the Graco Fusion AP (air-purge) spray gun and the Graco Fusion MP gun.Features Genuine Graco muffler One per gun Fits Fusion AP and Fusion MP Specifications Part number: 119626 Graco...

The Graco 203953 screw cap is a #10-24 x 3/8 in. (10 mm) fastener used across a wide range of Graco spray guns, from Fusion foam guns to Silver Plus airless guns.Plural-component guns see heat, pressure and isocyanate exposure every day, so scheduled replacement...

The Graco 15B209 trigger is the genuine replacement trigger for Graco Fusion AP and Fusion PC spray guns (ref. 13). A bent or cracked trigger can make the gun hard to actuate or keep the safety from engaging properly, so replace it as soon...

The Graco 15C480 wave washer is a genuine replacement part listed as ref. 20 in the Graco Fusion AP and Fusion PC spray gun parts lists. Replace it when it is flattened, corroded or lost during gun service.Features Genuine Graco wave washer Used on...

The Graco 192272 pin is the pivot pin listed as ref. 6 in the Graco Fusion AP and Fusion PC spray gun parts lists. It is the pin the trigger (15B209) pivots on.Features Genuine Graco pivot pin Used on both Fusion AP and Fusion...

Amaano 248132-D supplies fluid housing o-rings for the fluid housing on Graco Fusion AP guns, ready for scheduled rebuilds. Features Matches the Graco Fusion AP fluid housing position (Graco part 248132) Field-tested by spray foam contractors in addition to lab testing, per the supplier...

Amaano Fluid Housing O-Ring, Reusable (248132-R) is an aftermarket o-ring for the fluid housing position on Graco Fusion AP spray foam guns. Features Matches the Graco Fusion AP fluid housing position (Graco part 248132) Field-tested by spray foam contractors in addition to lab testing,...

The Graco 15K365 handle is the genuine replacement handle for Graco Fusion AP and Fusion PC plural-component spray guns (ref. 1 in both parts lists). A cracked or damaged handle affects grip and can compromise the air connection at the base of the gun,...

The Graco 116550 retaining ring is a genuine Graco retaining ring listed in the parts lists of both the Graco Fusion AP (air-purge) spray gun and the Graco Fusion MP (mechanical-purge) gun.Features Genuine Graco part 116550 Retaining ring, one per gun Fits Fusion AP...

Graco 248132 is a package of 6 O-rings for the Graco Fusion AP air-purge spray gun, used at the fluid housing / lock ring.Crews that spray foam or polyurea daily typically keep a stock of Fusion wear parts in the rig to avoid losing...

The Graco 15B215 lock ring is a genuine replacement part for the Graco Fusion AP air-purge plural-component spray gun (ref. 7). Replace it if it is cracked or no longer locks firmly.Features Genuine Graco lock ring Fits the Fusion AP air-purge gun Quick, inexpensive...

Graco 246356 is the fluid shutoff valve used in the manifold of Graco Fusion AP and Fusion PC plural-component spray guns.Rebuilding with genuine Graco parts keeps factory tolerances in the gun, which matters for mix quality in spray foam and polyurea work.Features Two used...

The Amaano 248129-R check valve housing o-ring is a replacement seal for the check valve housing of the Graco Fusion AP air purge gun. Features Matches the Graco Fusion AP check valve housing position (Graco part 248129) Field-tested by spray foam contractors in addition...

The Graco 15B221 bolt (5/16-24) secures the 2-hose fluid manifold (246012) to Graco Fusion AP and Fusion PC plural-component spray guns (ref. 12d). It is included with the manifold and also sold on its own for replacement.Features Genuine Graco manifold bolt Holds the fluid...

Keep your Fusion AP gun sealing properly with the Amaano Amaano Check Valve Housing O-Ring, Disposable (248129-D), made for the gun's check valve housing. Features Matches the Graco Fusion AP check valve housing position (Graco part 248129) Field-tested by spray foam contractors in addition...