Products

The Carlisle 336363 trigger is the replacement trigger for the Carlisle ST1 spray foam gun. It mounts with the 336364 trigger stud and 336365 trigger screw. The ST1 is rated to 3,500 psi and 200°F fluid temperature.Features Genuine Carlisle ST1 trigger Replaces a bent,...

The Carlisle 336365 trigger screw fastens the trigger on the Carlisle ST1 spray foam gun, together with the 336364 trigger stud. The ST1 uses an air-purge design with an integral air check valve to keep material out of the air passages.Features Genuine Carlisle part...

The Carlisle 336364 trigger stud is part of the trigger hardware on the Carlisle ST1 air-purge spray foam gun, used with the 336363 trigger and 336365 trigger screw. The ST1 is designed for single-tool field maintenance.Features Genuine Carlisle part 336364 Trigger mounting stud Related...

The TL-01 clevis extractor is a specialty tool for removing the clevis connection when servicing or rebuilding proportioner pumps.Features Controlled removal of the clevis without prying or hammering Reduces the risk of damaging rods and pins Speeds up pump teardown Specifications Stock number: TL-01...

The Crimp Hose Fitting, 1/2 in JIC x 3/8 in provides a 1/2 in JIC end on a crimped hose assembly (3/8 in size as listed). Crimp it onto the matching hose to build a finished hose assembly. Use it to make replacement fluid...

This Crimp Hose Fitting, 1/4 in JIC x 1/4 in provides a 1/4 in JIC end on a crimped hose assembly (1/4 in size as listed). Use it to make replacement fluid hoses to the length you need. Crimp it onto the matching hose...

Use this Crimp Hose Fitting, 3/8 in JIC x 1/4 in when a job calls for a part that provides a 3/8 in JIC end on a crimped hose assembly (1/4 in size as listed). Crimp it onto the matching hose to build a...

ArmorThane's Crimp Hose Fitting, 3/8 in JIC x 3/8 in provides a 3/8 in JIC end on a crimped hose assembly (3/8 in size as listed). Use it to make replacement fluid hoses to the length you need. Crimp it onto the matching hose...

The SUP101 desiccant cartridge dries incoming air so moisture is kept away from moisture-sensitive materials such as isocyanate (A-side) in drums, tanks and lube reservoirs.Features Absorbs water vapor from air drawn in as material is pumped out Helps prevent crystallization and contamination of A-side...

The SAF114 disposable dust mask is a light, single-use face mask for nuisance dust created while sanding, scuffing and cleaning surfaces ahead of a coating job.Features Disposable design – swap for a fresh mask as needed Handy for bed prep, scuffing and shop clean-up...

SAF112 disposable latex gloves, size XL, keep hands clean while mixing pigments, masking, handling primers and cleaning up after a spray job.Features Extra-large size for bigger hands Disposable – change pairs between tasks to avoid cross-contamination Useful for masking, mixing, touch-up and equipment maintenance...

E-Z Wire Trim Tape (PRE107) is a wire-reinforced trim tape used to create clean, professional edges where a sprayed coating meets an uncoated surface.Features Embedded wire helps cut a crisp line through fresh coating Ideal around bedliner rails, trim and body lines Reduces time...

The EQU122 electric air compressor supplies compressed air in a spray rig – for air-purge plural-component guns, air-driven transfer pumps and shop tools.Benefits Electric drive runs off rig or shop power Provides purge air for guns such as the Graco Fusion AP and Carlisle...

EZ Trim Fiber Tape (PRE104) is a fiber-reinforced trim tape for producing neat edges where sprayed bedliner or polyurea meets painted or trim surfaces.Features Fiber reinforcement for a clean pull and cut line Great around bed rails, tailgates and body lines Cuts down on...

The Female Quick Disconnect x 1/4 in MPT adds a female quick-disconnect socket to a 1/4 in female pipe port. Use it to add quick-connect points to compressors, air tools and air supply lines. It makes swapping hoses and tools faster in the shop...

SAF121 ear plugs give spray crews simple hearing protection around the noise of generators, air compressors, proportioners and grinders on the job.Features Easy to carry in a pocket or rig drawer Useful during surface prep with grinders and sanders Pairs with safety glasses and...

The GD high-temperature refrigerated air dryer (EQU123) cools compressed air to condense and remove moisture before it reaches your spray gun, pumps and air tools – an important step when spraying moisture-sensitive polyurea and foam.Benefits High-temperature design for hot compressor discharge air in rigs...

ArmorThane's Gear Hose Clamp, 7/16 in x 1 in tightens down on flexible hose over a barb or fitting. Keep a supply on hand for hose repairs. Use it wherever flexible hose slips over a barb or fitting.Features Stocked with ArmorThane's hose fittings Holds...

Graco 249200 is a 100 mesh handle filter for Graco airless spray guns, giving finer filtration for thin materials and small tips.Contractors who spray every day keep common gun parts in the truck so a worn part never stops the job.Features Fine 100 mesh...

The Graco 100016 is a genuine Graco lock washer used in the assemblies of Graco spray equipment.Features Genuine Graco hardware for an exact match to the parts list Helps keep fasteners from backing out under vibration Worth adding to the order whenever you replace...

The Graco 100139 pipe plug is a 1/8-27 NPT plug that appears in the fluid manifold of the Graco Fusion AP (air-purge) spray gun (two per gun) and is also listed in the Fusion CS and Fusion MP parts lists.Features Genuine Graco part 100139...

The Graco 100721 pipe plug is a 1/4-18 NPT plug listed on the Graco Fusion AP (air-purge) spray gun, where Graco notes it is used on round and flat pattern guns only. It is also listed in the Fusion CS and Fusion MP parts...

The Graco 100846 grease fitting is the zerk fitting used for lubrication on both the Graco Fusion AP (air-purge) spray gun and the Graco (GlasCraft) Probler P2 dispense gun. Replace it if it is clogged, broken or missing.Features Genuine Graco zerk/grease fitting One used...