armorthane

SUP-LFC lint-free cleaning towels wipe down substrates and equipment without leaving fibers that can show up in a finished coating.Features Lint-free for final wipe-down before priming or spraying Handy for cleaning guns, fittings and mix chambers Keep a supply in every rig Specifications Stock...

This Local / Remote Selector Switch selects between local and remote control on an equipment control panel. Contact ArmorThane for help confirming fit before ordering.Features Lets the operator choose between local and remote control Replacement part for equipment control panels Stocked by ArmorThane with...

PRE102 1-1/2" masking tape secures masking paper and sheeting and protects wider edges before spraying polyurea, bedliner and topcoats.Features 1-1/2" width for wider coverage along edges Holds masking paper and plastic sheeting in place Easy to tear by hand Specifications Stock number: PRE102 Width:...

PRE100 3/4" masking tape is a narrow tape for detail masking around trim, lights, fittings and tight curves before spraying.Features 3/4" width follows curves and small parts Use with masking paper and trim tape for complete protection Tears cleanly by hand Specifications Stock number:...

NMP (N-methyl-2-pyrrolidone) is a strong polar solvent that applicators use for cleaning polyurea and polyurethane spray equipment, guns and parts. ArmorThane stocks it with its other shop cleaners.Features Powerful solvent for equipment cleanup Useful for soaking gun parts and cleaning components Available from ArmorThane...

The PFX (EQU508) is a plural-component proportioner offered in ArmorThane's high-pressure equipment lineup for spray foam and coatings applicators. Specifications Stock number: EQU508 FAQ How do I get full specifications? Call ArmorThane at (417) 831-5090 for the current configuration, output and power requirements, and...

The ArmorThane GUN131 pin vise is a hand tool for holding the small cleaning drills used to clear mix chamber nozzles and impingement ports on plural-component spray foam and polyurea guns. Turning drills by hand gives control and helps avoid enlarging or damaging the...

The ArmorThane PKG150 P2 gun 01 drill bit kit contains cleaning drills for the 01 mix chamber on the Graco/GlasCraft Probler P2 dispense gun. Regular drilling of the nozzle and impingement ports removes cured material that distorts the pattern.Features Drills sized for the P2...

The ArmorThane PKG151 P2 gun 02 drill bit kit is for cleaning the 02 mix chamber on the Graco/GlasCraft Probler P2 gun. Higher-output 02 chambers see a lot of material, and a quick pass with the right drill keeps them flowing.Features Drills sized for...

The ArmorThane PKG152 P2 gun 03 drill bit kit supplies cleaning drills for the 03 mix chamber (Graco GC2503) on the Graco/GlasCraft Probler P2 gun, used for high-output foam and polyurea application.Features Drills sized for the P2 03 chamber Clears cured material without enlarging...

The ArmorThane PKG153 P2 AA drill bit kit supplies cleaning drills for the AA mix chamber, the smallest round chamber on the Graco/GlasCraft Probler P2 gun. Small AA ports plug quickly, so the right drills are essential for daily cleaning.Features Drills sized for the...

The TL-02 ball seat removal tool is a service tool for pulling ball seats from proportioner pump check-valve assemblies during rebuilds.Features Purpose-made for seat removal – less risk of scoring bores than improvised tools Speeds up pump rebuilds and check-valve service Keep one with...

The SUP104 quart mixing bucket is a small container for mixing and measuring pigments, primers, roll-on topcoats and touch-up batches.Features Quart size for small, controlled batches Useful for pigment pre-mixing and primer mixing Keeps small jobs neat and waste low Specifications Stock number: SUP104...

The EQU-RAD refrigerated air dryer removes water vapor from compressed air by chilling it, so the air reaching your plural-component gun, transfer pumps and tools is drier.Benefits Reduces moisture contamination at the gun and in air-driven pumps Helps protect isocyanate (A-side) from moisture exposure...

The EQU-REF refrigerated unit is a refrigerated air-drying component for spray rig compressed-air systems, used to reduce moisture before air reaches guns and pumps.Benefits Drier compressed air for plural-component gun purge Helps limit moisture reaching moisture-sensitive coatings Replacement or add-on for rig air systems...

SUP107 replacement blades keep your trim knife sharp for cutting masking paper, sheeting and tape lines, and for trimming coating edges.Features Fresh edges for clean, straight cuts Swap dull blades instead of tearing masking Designed to pair with the ArmorThane trim knife (SUP106) Specifications...

SAF117 safety glasses protect applicators' eyes during surface prep, grinding, masking and routine equipment service.Features Everyday eye protection for prep and shop work Lightweight enough to wear all shift Keep several pairs in the rig for helpers and visitors Specifications Stock number: SAF117 Type:...

SUP103 sanding pads scuff and profile surfaces so primers, polyurea and bedliner coatings have something to grip.Features Scuff paint, plastic and metal before coating Reach corners and contours by hand Improves mechanical bond when used with the correct primer Specifications Stock number: SUP103 Type:...

The SUP105 scuffing cup brush is a rotary cup brush for quickly scuffing large areas such as truck beds and equipment before applying bedliner or polyurea.Features Covers large areas faster than hand sanding Helps create a profile for primer and coating adhesion Reaches into...

SUP102 silica beads are a desiccant media that absorbs moisture from air – used to help keep moisture away from isocyanate and other moisture-sensitive materials.Features Absorbs water vapor from surrounding air Helps protect moisture-sensitive A-side material Simple, low-cost moisture control Specifications Stock number: SUP102...

The spool valve rebuild kit (GUN-SVRK) contains replacement parts for servicing the spool valve in a plural-component spray gun handle. The spool valve directs trigger air to open and close the gun, so worn parts show up as air leaks, a sticky trigger or...

The SAF101 head sock is a stretch head cover worn by spray applicators to keep overspray off the hair, ears and neck while spraying polyurea, bedliners and spray foam.Features Covers hair, ears and neck under a respirator, hood or face shield Helps keep sticky...