High Pressure Gun Parts

Keep your Fusion AP gun sealing properly with the Amaano Amaano Fluid Block O-Ring, Disposable (248131-D), made for the gun's fluid block. Features Matches the Graco Fusion AP fluid block position (Graco part 248131) Field-tested by spray foam contractors in addition to lab testing,...

The Graco 15B211 retaining ring is the front retaining ring on the Graco Fusion AP air-purge plural-component spray gun (ref. 9). It holds the front-end components in place and is removed during mix-chamber and air-cap service.Features Genuine Graco retaining ring Fits the Fusion AP...

The Graco 2000974 Fusion FX hose manifold assembly connects the heated whip hoses to the Graco Fusion FX spray gun. It carries the A- and B-side filter housings, check manifold housings and manual fluid valves, and mounts to the gun with the manifold bolt.Features...

The Graco 2009349 Fusion FX flat air cap kit lets the Fusion FX gun run Graco's flat spray tips for a fan pattern, the style many polyurea and coatings applicators prefer for even film build on floors, walls and truck beds.Features Converts the FX...

The Graco 2005267 extension tip cap (37–42) extends the front of the Graco Fusion FX gun for mid-size round mix chambers, giving a tighter, longer-throw pattern for reaching high walls, deep cavities or tight framing bays.Features Longer reach without moving the rig Tighter pattern...

The Graco 2005268 extension tip cap (47–70) is the largest Fusion FX extension tip, for use with the bigger round mix chambers. It extends the gun's reach while giving a controlled pattern on high-output foam and polyurea work.Features Built for larger FX round chambers...

The Graco 2000975 Fusion FX manifold fluid valve kit includes two fluid valves for the Fusion FX hose manifold. These valves let you shut off the A and B materials at the gun, so worn or leaking valves should be replaced promptly.Features Two valves...

The Graco 2006355 Fusion FX shutdown grease cartridge is a single cartridge of the shutdown grease Graco specifies for the Fusion FX spray gun. Graco describes the grease as specially formulated low-viscosity grease that flows easily through gun passages to prevent two-component curing and...

The Graco 2000978 Fusion FX CS air piston kit is the complete piston assembly for the Graco Fusion FX plural-component spray gun. Graco's parts list shows it built from the CS air piston with o-rings, the safety stem stop, the dosing piston, a spiral...

The Graco 2005266 Fusion FX extension tip cap (34–42) fits over the front of the Fusion FX gun to extend reach and tighten the spray pattern from smaller round mix chambers. It helps when you need to reach into cavities or spray farther without...

The Graco 2001168 Fusion FX check manifold housing kit replaces the check housings in the Fusion FX hose manifold, which uses two. Healthy checks help keep A and B materials from backing up into the opposite side.Features Kit covers both check housings (qty 2)...

The Graco 2000811 is a 3 pack of replaceable FX fluid cartridges for the Graco Fusion FX spray gun. The cartridge controls fluid flow through the gun's impingement mixing and houses the shuttle valves that switch between fluid and air purge, so a fresh...

The Graco 2007352 is a 10 pack of 3 oz shutdown grease cartridges for the Graco Fusion FX spray gun. Graco formulates this low-viscosity grease to flow easily through the gun's passages, preventing two-component curing and keeping fluid passages clean between jobs.Features Ten 3...

The Graco FX52FL is the flat-pattern mix chamber for the Graco Fusion FX spray gun, with 0.051 in. impingement ports. Flat patterns are favored by many polyurea and coatings applicators for even film build on floors, walls and liners.Features Flat fan pattern for coatings...

The Graco 2001307 Fusion FX o-ring repair kit bundles the assorted o-rings needed for routine maintenance on the Graco Fusion FX spray gun. Replacing o-rings as a set during scheduled service helps prevent air and fluid leaks that lead to downtime.Features Multiple o-ring sizes...

The Graco 2007251 CS check o-ring kit reseals the check area of the Fusion FX fluid cartridge on the Graco Fusion FX spray gun. Fresh o-rings here help prevent leaks and keep the A and B sides separated until they reach the mix chamber.Features...

The Graco 119421 o-ring is used in several places on the Graco Fusion FX spray gun. Graco's parts list shows it in the CS piston assembly (three per assembly) and in the gun body (four), making it one of the most commonly replaced o-rings...

The Graco 2000812 5 pack supplies five replaceable FX fluid cartridges for the Graco Fusion FX spray gun. For crews running the FX every day, a stack of spare cartridges means a fouled cartridge is a quick swap instead of a lost afternoon.Features Best...

The Graco 2005366 Fusion FX MC seal kit contains ten mix chamber seals for the Graco Fusion FX spray gun. The seal sits at the mix chamber, and a worn seal can leak or let material bypass, so replacing it on a regular schedule...

The Graco FX60RD round mix chamber is a high-output option for the Graco Fusion FX spray gun, with 0.057 in. impingement ports and a 0.087 in. nozzle. It is sized for large proportioners and big open areas.Features High output for large-area work Round pattern...

The Graco FX70RD is the largest round mix chamber for the Graco Fusion FX spray gun, with 0.061 in. impingement ports and a 0.0945 in. nozzle. It is meant for maximum-output spray foam and coatings work on high-capacity rigs.Features Largest FX round chamber for...

The Graco FX52RD round mix chamber for the Graco Fusion FX spray gun has 0.052 in. impingement ports and a 0.08 in. nozzle. It covers the upper-mid output range and works with Graco's larger extension tip cap for long-reach spraying.Features Upper-mid output range Round...

The Graco 2006566 Fusion FX complete spare parts kit packs the common wear parts for the Graco Fusion FX spray gun into one refillable case. It is built for spray foam and polyurea crews who want to fix the gun on site instead of...